Problem with brakes and pantograph Vectron pack CZ/SK

B

Bpee237

Cestující
Good evening,

I have big problems with the VECTRON engines from the VECTRON Pack for OR CZ/SK.
First one is, after the first braking with the train brakes, the brake cylinder always fill again and the yellow lines on the right display appear again. I can not release the brakes after that.

And the second one is, that after the new update, the 2nd and 3rd pantographs are always up and can not taken down. Only the 1st and the 4th pantographs work normal? Does anyone have the same problems or any ideas how to fix them?
I am not able to drive this nice Vectron locos right now.

Thank you and greetings
Bpee237
 
Dobrý večer,

opět pro ty z vás, kteří neumí anglicky.

Mám velké problémy s motory VECTRON z VECTRON Packu pro OR CZ/SK.
První je, že po prvním zabrzdění vlakovými brzdami se brzdový válec vždy znovu naplní a opět se objeví žluté čáry na pravém displeji. Nemohu poté uvolnit brzdy.

A druhý je ten, že po nové aktualizaci jsou 2. a 3. pantografy vždy nahoře a nejde sundat. Funguje normálně jen 1. a 4. pantograf? Má někdo stejný problém nebo nějaký nápad jak je opravit?
Momentálně nejsem schopen řídit tuto pěknou lokomotivu Vectron.

Děkuji a zdravím
Bpee237
 
Bpee237 napsal:
Good evening,

I have big problems with the VECTRON engines from the VECTRON Pack for OR CZ/SK.
First one is, after the first braking with the train brakes, the brake cylinder always fill again and the yellow lines on the right display appear again. I can not release the brakes after that.

And the second one is, that after the new update, the 2nd and 3rd pantographs are always up and can not taken down. Only the 1st and the 4th pantographs work normal? Does anyone have the same problems or any ideas how to fix them?
I am not able to drive this nice Vectron locos right now.

Thank you and greetings
Bpee237
Rozbalte kliknutím...
Update the program to the latest version from 5.4. 2024.
 
Adam Stahl napsal:
Update the program to the latest version from 5.4. 2024.
Rozbalte kliknutím...
I had the problem some time ago too. There is no new version for OR CZ7SK an the website msts-rw.cz The 1.8.216 is the newest and the Vectron pack is from the 09.03.24 which started the problem with the pantographs.
 
1.8.216 cannot be the latest, now updated to 612 on 5.4.2024obrázok_2024-04-06_001020773.jpeg
Check if you have installed the correct way that Pack Vectron, reinstalling might help. Personally, I don't have any problems.
 
I think I could solve the breaks problem. I used the highpressure release which made problems. When I press Ö until the breaks release position and then wait until the yellow lines are gone the breaks work normal.

But the pantographs problem is still there. From the start of OR the two middle pantographs are upside and don't work. Only the first one and the last work. I have installed the VECTRON pack new, this problem only appears after the new update from 9.3.24
 
Please let us know what version of OR CZ/SK you are using. Give me a picture where you can see the version.
 
I have used the Version v1.8.216 where the Vectrons does not work. Or said it has found a new version but the update did not work, because one file was already on my PC (which should be normal for updates)
Yesterday I downloaded the OR CZ/SK from the website again and installed it. It is the v1.8.618 which works fine with the Vectrons.
So problem sloved. Thank you all for your ideas.

Greetings Bpee237
 
I have used version 1.8.623 from 10.04.2024
Panto 1 raised automatically at start
not possible to raise an other panto, bo reaction on P, shift-P, ctrl-P
I have used Vectron 193 227 rom msts-rw site

Greetings gscraisd
 
i did explore route in automode, loco is vectron ctrl + Alt + x no reaction, also no command output on screen
tacho still 0 kmh no movemement of needle
 
OR 1.8 tacho in "explore route" -> ok, in "explore in activity mode" -> not ok
OR 1.5 tacho in "explore route" -> ok, in "explore in activity mode" -> ok
 
Unfortunately I have the brakes problem again with the Vectrons. It does not appear every time but sometimes the trainbrake cylinders fill again directly after (highpressure)release.
The only way to slove this is opening the bleed of ventil on every wagon. There is no way to release the brakes from the loco anymore.
 
Pro psaní příspěvků je nutné se přihlásit či zaregistrovat.
Back
Nahoře